BrainFPV RADIX LI & Talon 35A ESC 20X20 Combo


Out of stock
  • Category: ESC'S + 4IN1 + STACKS
  • SKU: 87998

Price:AU$158.00


Out of stock

Description

Looking for the perfect 6S companion for your GigaBrain!! Available exclusively at Heli-Nation! The BrainFPV RADIX and Talon Gigawatt 35A ESC combine to give you a powerful 6S 20X20 stack with BrainFPV's famous Graphical OSD!


1. BrainFPV RADIX LI FC

THE WORLDS FIRST 20 x 20 FLIGHT CONTROLLER WITH A GRAPHICAL OSD

Processor: STM32F446RET6, Coretx-M4, 32bit, 180MHz, 128kB RAM, 512kB Flash.
IMU: Bosch Sensortec BMI160 running at 3.2kHz, connected using SPI.
OSD: Full-graphic, PAL/NTSC auto detect, adjustable black and white levels. Full Betaflight OSD support with extra graphical features. Support for side-by-side 3D when used with a 3D FPV camera.
Motor Outputs: 6 outputs with full DSHOT (150/300/600/1200) and OneShot support.
Receiver Support: PPM, S.Bus (inverter built-in), DSM, HoTT, SRXL, CSRF, FPort ready. 5V or 3.3V supply for receiver. Receiver is powered from USB for easy and safe setup.
Telemetry Support: FrSKY Smart Port, FrSKY Sensor Hub, HoTT Telemetry, SRXL, CSRF, FPort ready. Built-in inverter for FrSKY telemetry.
Serial Ports: 4 full serial ports (UARTs). UART3 and UART6 have inverters for S.Bus and SmartPort telemetry. Inverters are automatically enabled/disabled for maximum flexibility.
RGB LEDs: Dedicated RGB LED output.
Camera Control: Dedicated output for accessing the camera menu to change camera settings.
Buzzer Port: Dedicated port for 5V (100mA max) buzzers.
Analog Inputs: Voltage sensing (VBAT), current input (3.3V max).
Power: 3S - 6S (7.5V - 26V), 500mA BEC
Dimensions: 26.5mm x 26.5mm, 20mm hole spacing. 4.1mm holes for anti-vibration grommets for M3 screws.
Weight: 4g

Gluten free, Non GMO, Free Range Anorganic Gyro


2. Talon Gigawatt 35A ESC

The Talon Gigawatt 4-in-1 35A 6S is a new generation ESC that uses a variety of bleeding edge technologies in hardware and firmware.

The Talon Gigawatt is worth your investment.
BLHeli_32 code base
Programmable PWM frequency of up to 48KHz
Auto-timing for higher efficiency and reliability
Analog Voltage/Current sensing
Adjustable “Brake on Stop” force
Improve direction change in Bidirectional mode
One current sensor to measure the total amp draw and telemetry functions.
ESC Telemetry (Voltage and RPMs and current)
Configuring from FC using DShot commands
Programmable sine modulation mode
Programmable soft bidirectional mode
Programmable autonomous periodic (every 32ms) telemetry mode
Hardware noise filter on the signal input

ATTENTION: 

Please use the "make your own harness" that's included with the BrainFPV RADIX LI. Colors of wires in illustration are only to make the wires easier to follow and DO NOT represent the colors of the wires on the harness. The complete harness that comes with the RADIX DOES NOT work with this ESC and will cause damage if used. Please use the included kit to make the correct harness.